RELI-DA01/r lightline dali-converter ac/dc with 5 year warranty 1.6 watt dali- converter selection guide input voltage range 90-290vac, 50/60hz power consumption 1.6w typ. / 3w max. dali bus current consumption 2ma max. suitable electric wire 22 awg - 16 awg pwm frequency 500hz typ. pwm high level voltage 9.5vdc min. / 10vdc typ. / 10.5vdc max. pwm low level voltage 0vdc typ. pwm output current sourcing (ma) -60ma min. / 60ma max. dc 0/1-10v output accuracy 3% dc output current sourcing (ma) -5ma min. / 60ma max. dali standard iec62386 part-102 & part-206 short circuit protection (dimming output) cont., current limited to 240ma over voltage protection (dali connector) 24v zener diode clamp operating temperature range ambient temperature -20 to +40c (free air convenction) case temperature 46c relay switch 1 channel, 2a cont. / 70a inrush handling ip rating ip20 dimensions 150 x 40 x 28mm weight 100g 10% safety standards (100-240vac) report: p201311017 en61347-1, 2nd edition en61347-2-11, 1st edition emc emmission report: ha140050 iec61000-3-2, 3 en55015 emc immunity iec61000-4-2,3,4,5,6, 8, 11; class a en61547 mtbf (+25c) using mil-hdbk 217f 200 x 103 hours min. specifications (measured at t a = 25c and nominal input voltage) compliant with dali standard (iec62386 part 102 & part 206) screw-less connectors, easy to install selectable output for dc 0-10v / dc 1-10 / pwm built-in relay to turn on/off driver completely (zero standby current) over voltage and short circuit protection features dali converter part input power dali bus dali dimming number voltage consumption power consumption standard output (vac) (w) (ma) iec62386 RELI-DA01/r 90-290 1.6 typ. 2 max. part-102 dc 0-10v part-206 dc 1-10v or pwm (1) note1: pwm output is not included in the iec62386 standard iec 62386-102 compliant iec 62386-206 compliant en55015 certified en61347 certified en61547 certified description the RELI-DA01/r is a dali to analog control signal interface which is compliant with the dali iec62386 standard and listed on the agdali website.. the output is selectable between 0-10v and 1-10v or pwm (1) and is compatible with all recom dimmable led drivers as well as other manufacturers products. the output can control several led drivers, allowing the lighting in a whole room or office to be dimmed with just one dali address. a built-in relay can be used to switch off the led drivers under software control to give zero no-load consumption. the interface is universal ac powered (110vac, 230vac or 277vac). refer to application notes rohs 2011/65/eu 6/6 l-72 www.recom-power.com rev: 0/2015
RELI-DA01/r typical characteristics RELI-DA01/r series lightline ac/dc-converter variable default value reset value range of validity actual dim level 254 254 0, min level - max level power on level 254 254 0 - 255 (mask) system failure level 254 254 0 - 255 (mask) min level physical min level physical min level physical min level - max level max level 254 254 min level - 254 fade rate 7 (45 steps/s) 7 (45 steps/s) 1-15 fade time 0 (no fade) 0 (no fade) 0-15 short address 255 (mask) no change 0-63 255 (mask) search address ff ff ff ff ff ff 00 00 00 - ff ff ff random address ff ff ff ff ff ff 00 00 00 - ff ff ff group 0-7 0000 0000 (no group) 0000 0000 (no group) 0 - 255 group 8-15 0000 0000 (no group) 0000 0000 (no group) 0 - 255 group 0-15 255 (mask) 255 (mask) 0 - 255 (mask) status information 1xx0 xxxx 0x10 0xxx 0 - 255 version number 1 no change factory-defined x = actual value depend on the operation status dali declaration for f actory variables (for part 102) dali declaration for f actory variables (for part 206) variable default value reset value received command range of validity dimming curve 0 no change 0 0-1; (2 - 255 reserved) converter features 0011 a101 no change 0011 a101 53; 61 failure status 0000 0000 no change 0000 0000 0 - 255 converter status 0000 0000 no change 0000 0000 0 - 255 extended version number 1 no change 1 factory-defined device type 5 no change 5 factory-defined physical min level 1 no change 1 1-253 a = 0 relay function dissabled; a = 1 relay function enabled dali command set command number command name function - direct arc power set directly the light level 0 off switch off the light 1 up dim up the light 2 down dim down the light 5 recall max recall the maximum light level 6 recall min recall the minimum light level the RELI-DA01/r has been accepted by agdali as conforming to the dali standard for control gear (iec 62386-102) and device type 5 (iec 62386-206). it supports all relevant commands of the defined command set. not supported commands include the query lamp failure and the query lamp power on. additionally the features to disable the relay switch, set the output to pwm, change the pwm from active- high to active-low are additional and not tested by dali (refer to the RELI-DA01/r instruction manual). www.recom-power.com l-73 rev: 0/2015
RELI-DA01/r series lightline ac/dc-converter typical characteristics
dali-command logarithmic dimming; 1-10v 6 recall min level 257 data transfer register (dtr) / value: 0 dec 272 enable device type x / value: 5 dec 224 query app ext cmd224 224 query app ext cmd224 272 enable device type x / value: 5 dec 229 query app ext cmd229 229 query app ext cmd229 internal switch: off dali connection 9 *2)+!"696 )* 7)-0 +) ) 780)67 2602 5
(>
5 8-/k 9 ) ) ) 4 9 2) 2) 12 02 1 0 @#@# )8 ) ) 1 0 1
(> 05 ) )8 @= )8 1 0 9 2) 2) ) 5
ac/dc led driver dc/dc led driver dali master racd20-xxxd rcd24-xxx custom commands tested with dali-usb racd60-xxxxa rcd48-xxx tridonic osram (iec62386 compatibility racd45-xxxxa rbd12-xxx confirmed by dial ag using prohibit tester) racd100-xxxxa racd150-xxxxa *software masterconfigurator v2.6.8.1005 tridonic note: for one dali converter (RELI-DA01/r) up to 6pcs of recom ac/dc led-drivers with 3in1 dimming can be connected. recommended led drivers, dali-bus power supplies and dali master l-74 www.recom-power.com rev: 0/2015
RELI-DA01/r RELI-DA01/r series lightline ac/dc-converter package style 9 indicator led flashes with dali signal on / off pwm / dc by internal switch 9 on: pwm 10v (default active high) off: dc 1-10v (default dc) dc 0-10v (software control) delivery setting: output signal: dc 1-10v dimming curve: logarithmic pwm active high refer to instruction sheet for dali commands for alternate settings (linear dimming curve, dc 0-10v, pwm active low, independen t relay control) $ dimensions www.recom-power.com l-75 rev: 0/2015 the product information and specifications are subject to change without prior notice. recom products are not authorized for us e in safety-critical applications (such as life support) without recoms explicit written consent. a safety-critical application is defined as an applica tion where a failure of a recom product may reasonably b e expected to endanger or cause loss of life, inflict bodily harm or damage property. the buyer shall indemnify and hold harmless recom, its affiliated companies and its representatives against any damage claims in connecti on with the unauthorized use of recom products in such safety-critical applications.
|
